高分子絮凝剂处理高浓度化妆品原料生产废水研究

化妆品原料生产过程中产生的废水水质成分复杂、有机物含量高、难降解，利用混凝工艺处理该废水能够减缓生化处理单元的负担，提高污水处理效率。为揭示无机高分子混凝剂混凝过程中污染物的去除机制和污泥性质的变化，考察了不同的絮凝剂聚合氯化铝（PAC）、聚合硫酸铁（PFS）、聚合氯化铝铁（PAFC）和助凝剂聚丙烯酰胺（PAM）投加浓度对污染物去除率和污泥性质的影响。采用傅里叶变换红外光谱（FTIR）、X射线能谱（EDX）、扫描电镜（SEM）、热重分析仪（TGA）分析污泥絮体官能团、表面形貌、元素组成和热稳定性的变化，采用三维荧光光谱（3D-EEM）和超滤技术分析出水中有机物分子量的分布规律和有机物成分的变化，优化最佳混凝工艺运行条件。结果表明：进水中的天然有机物（NOM）荧光强度高，有机物分子量主要分布在>100×10³和<3×10³区间，其所占比例分别为22.89%和50.57%。当进水COD为6700~7500 mg/L时，在助凝剂PAM投加浓度为0.03 g/L，PAC、PFS和PAFC投加浓度分别为2.8 g/L、2.8 g/L和3.0 g/L的条件下，COD去除率分别为87.20%、79.89%和83.74%，出水浊度分别为2.54 NTU、9.3 NTU和5.51 NTU，NOM荧光强度大大减弱。其中，PAC+PAM对废水中有机物去除效果最好，出水有机物分子量主要分布在(10~30)×10³和<3×10³范围内，其所占比例分别为31.84%和25.92%，形成的混凝污泥具有较好的热稳定性，污泥表面蓬松,呈多孔网状结构。混凝工艺可吸附脂类大分子物质，提高了高浓度化妆品原料生产废水的可生化性。     

金属基聚合物内衬复合压力容器界面剥离失效及预防

基于构建的裂纹剥离扩展失效过程的模拟方法，提出了预测临界载荷的方法，并通过界面的临界应变能释放率与损伤起始应力，构建了预防界面裂纹剥离扩展失效的等值临界真空压力约束预防控制线和设计准则。结果表明，临界压力载荷受控于界面初始预裂纹长度、复合界面的临界应变能释放率（GIC）和损伤起始应力（T0），与界面初始预裂纹长度呈负关联关系，而与临界应变能释放率与损伤起始应力呈正关联关系；当初始预裂纹长度由11.11 %增至15.55 %时，临界压力载荷（Pc）由87.6 kPa降至为57 kPa，降幅为34.9 %；内衬界面剥离韧性参数（T0，GIC）的坐标点位于等值临界真空压力约束控制线之上，可有效预防内衬界面剥离扩展失效。     

PP/PCL/石墨/碳纳米管复合材料的制备及电性能分析

采用熔融共混法制备了石墨（G）、碳纳米管（CNTs）与聚丙烯（PP）、聚己内酯（PCL）导电复合材料，通过改变G的添加量制备了系列导电复合材料。主要测试了熔体流动速率、力学性能、导电性能、电热性能，并进行了电子显微镜观察结构、差示扫描量热法分析、热失重分析。结果表明，PCL与PP混合后，PP的拉伸强度提升了4.375 MPa，在加入G/CNTs之后，力学性能受影响较大下降了约73.5 %；G/CNTs的加入还能有效降低PP的电阻率，使其从绝缘体变为半导体材料电阻率为7.83×10⁶ Ω·m；PP与PCL共混后复合材料的热稳定性得到了显著提高，初始分解温度从368.88 ℃升高至398.95 ℃，在加入G/CNTs管后又进一步提高至408.78 ℃。     

Synthesis of hexacelsian barium aluminosilicate by film boiling chemical vapour process

An original oxide/oxide ceramic-matrix composite containing mullite-based fibers and a barium aluminosilicate matrix has been synthesized by the film boiling chemical vapour infiltration process. Alkoxides were used as liquid precursors for aluminum, silicon and barium oxides. The structure and microstructure of the oxide matrix were characterized by Scanning Electron Microscopy, Energy Dispersive Spectroscopy and X-ray diffraction. Apart from small residual mullite and amorphous phase amounts, the oxide matrix is composed of the hexacelsian phase, conferring to the material interesting perspectives for high-temperature electromagnetic and structural applications.     

Mechanophysical Cues in Extracellular Matrix Regulation of Cell Behavior

The extracellular matrix (ECM) is a macromolecular network that can provide biochemical and structural support for cell adhesion and formation. It regulates cell behavior by influencing biochemical and physical cues. It is a dynamic structure whose components are modified, degraded, or deposited during connective tissue development, giving tissues strength and structural integrity. The physical properties of the natural ECM environment control the design of naturally or synthetically derived biomaterials to guide cell function in tissue engineering. Tissue engineering is an important field that explores physical cues of the ECM to produce new viable tissue for medical applications, such as in organ transplant and organ recovery. Understanding how the ECM exerts physical effects on cell behavior, when cells are seeded in synthetic ECM scaffolds, is of utmost importance. Herein we review recent findings in this area that report on cell behaviors in a variety of ECMs with different physical properties, i.e., topology, geometry, dimensionality, stiffness, and tension.     

基于广义逆矩阵理论的杆系结构形态创构方法#br#

广义逆矩阵理论被广泛应用于不稳定结构的形态分析。不稳定结构在荷载作用下，其形状会发生变化直至其势能达到最低，此时的结构处于无弯矩的平衡状态。根据该原理并结合广义逆矩阵理论提出一种适用于杆系结构的形态创构方法。该方法将杆系模型中杆单元进行分组，在每一组中杆单元总长度不变的条件下，建立控制结构形状变化的移形方程。利用广义逆矩阵理论和势能梯度确定使模型势能下降最快的方向，并逐步调整节点位置直至势能达到最低。临时单元和单元组的引入使得该方法可以应用于多种形式结构的形态创构，合理地设置单元组和临时单元可以实现单元长度与单元内力的重新分配进而实现诸多功能。算例分析说明该方法的特性并验证其有效性。     

薄煤层复合顶板巷道支护参数优化研究

以滨湖煤矿12210工作面材料巷为研究背景,在原有巷道支护方案的基础上,提出了2种巷道支护参数优化方案。运用FLAC3D数值模拟软件对原方案、方案1、方案2进行了分析对比。通过对不同方案下的巷道垂直、水平应力和位移云图分析研究发现,支护方案2为最优方案。方案2的支护密度相对原方案有所降低,因此,方案2在一定程度上节约了滨湖煤矿的支护费用和施工成本,提高了企业的经济效益。     

Magnetoelectric,magnetodielectric effect and dielectric,magnetic properties of microwave-sintered lead-free x(Co0.9Ni0.1Fe2O4)-(1-x)[0.5(Ba0.7Ca0.3TiO3)-0.5(BaZr0.2Ti0.8O3)] particulate multiferroic composite

Materials with two distinct (magnetostrictive-ferroelectric) phases, i.e., x (Co_0·9Ni_0·1Fe₂O₄) -(1-x) [0.5 (Ba_0·7Ca_0·3TiO₃) −0.5 (BaZr_0·2Ti_0·8O₃)], combined at ratios of 10:90, 20:80, 30:70, and 40:60 were prepared using a hydroxide coprecipitation method. These multiferroic composites were subjected to sintering via the hybrid microwave sintering technique at 1200 °C for 20 min. Ni-substituted CFO exhibited excellent magnetic properties at room temperature, with Ms ≈ 80 emu/g, μB ≈ 3.37, Mr ≈ 19.05 emu/g, and Hc ≈ 599 Oe, as well as a high value of the magnetostriction coefficient (λ12 ≈ −118 ppm). The magnetostrictive-ferroelectric crystal phases in each composite were confirmed via X-ray diffraction analysis. The highest value of the linear magneto-electric coefficient was α = 21.6 mV/cm-Oe at a frequency of 1 kHz for the 40CNFO-60(BCT-BZT) composite, and a similar sample had the highest value of the magnetodielectric coefficient, which was approximately 3.3% at f = 1 kHz with an applied magnetic field of 1 T. The typical ferromagnetic and ferroelectric nature of each composite was confirmed by M − H and P–E hysteresis loops, respectively at room temperature. Two anomalies were observed in the temperature-dependent dielectric permittivity one at ~140 °C and another above 500 °C confirming the coexistence of two materials with distinct transition points, i.e., BCT-BZT and CNFO, respectively.     

锂电池回收再生石墨增强水泥性能研究

废弃锂离子电池的负极活性材料主要为石墨,现阶段对于废弃锂离子电池中的石墨主要采用填埋等方法进行处理,造成了资源的浪费和环境的污染。现有的研究表明,废弃锂离子电池中的石墨经高温热解及酸浸处理后可以得到纯净的再生石墨,采用再生石墨增强水泥基复合材料的力学性能和电学性能。结果表明：再生石墨的引入可以增强材料的抗压性能和抗折性能,最大增幅分别达到了57.3%和84.4%。此外,再生石墨的加入有效降低了材料的电阻率,减少了极化时间,当再生石墨的掺加量为3%时,养护28 d后材料的电阻率仅为249 Ω·cm。该复合材料还具有典型的压敏特性。所制备的复合材料有望用于混凝土材料结构的实时动态监测。此外,对于废弃锂离子电池的全组分回收利用及功能水泥材料的研发具有重要意义。